Machine Information

MITCHELL PP-435 150,000 LB SINGLE DIE HYDRAULIC PUSH POINTER FOR TUBE

Stock #: 116367

Equipped With

SERIAL NO.                         PP-453
TUBE MATERIAL:                     ZR-2 TUBING, COPPER OR ALUMINUM
TUBE SIZE RANGE:                   5" MAX OD (PER MFG. SPECS)
                                   2" MIN OD (PER MFG. SPECS)
                                   3/8" MAX WALL
CAPACITIES:.
DIE ADVANCE - RATED:             150,000 LBS AT 1949 PSI
 DIE ADVANCE - MAXIMUM:          192,400 LBS AT 2500 PSI
CLAMP HOLDING:                   ADJUSTABLE UP TO MAX
                                 475,000 LBS AT 5000 PSI
SPEEDS:
DIE ADVANCE :                    79.6 IPM AT 2000 PSI
DIE RETURN:                      172.0 IPM AT 1000 PSI
CLAMP ADVANCE:                   68.1 IPM @ 1000 PSI

CLAMP RETURN:                    114.3 IPM AT 1000 PSI
DIE HOLDER:                      SINGLE "U" SHAPED
                                 OPEN TOP CAVITY TO
                                 ACCEPT ROUND CASE
                                 POINTING DIES
CYCLES:
AUTOMATIC                         ONE PUSH
SEMI-AUTOMATIC                    TWO PUSH WITH MANUAL DIE CHANGE
POINT LENGTH                      ADJUSTABLE TO 14" MAX. (PARALLEL SECTION)
METHOD OF KEEPING
POINT STRAIGHT:                  PATENTED AIR CYLINDER
                                 OPERATED CONICAL POINT FOLLOWER
DIE CROSSHEAD TRAVEL.             18"
JAW SIZE - PER HALF .              3-7/8" TK. X 6-3/8" WIDE X 18" LG.
                                 HARDENED STEEL FOR 3.75" O.D. TUBE
METHOD OF CHANGING DIES:         MANUAL - APPROX 40 LBS

                                 FOR 8" OD DIE
METHOD OF CHANGING JAWS:         MANUAL - APPROX 65 LBS
                                 PER HALF
MAX. OPENING BETWEEN JAWS:       3-3/4"
CLAMP MECHANISM:                 DIRECT ACTING HYDRAULIC CYLINDER
 
HYDRAULIC PUMPS:
CLAMP & PUSH                     VICKERS VANE TYPE
                                 26.5 GPM AT 2000 PSI AT 1200 RPM
CLAMP SEALING:                   OILGEAR PISTON TYPE
                                 1.72 GPM AT 5000 PSI AT 1200 RPM
HYDRAULIC RESERVOIR:             150 GALLON CAPACITY
HYDRAULIC FLUID:                 PETROLEUM OIL
                                 150-315 SUS AT 100 DEGREE F
 
HYDRAULIC PUMP DRIVE MOTOR:      50HP, 1200 RPM, 460 V.,



                                 3 PH., 60 HZ., DOUBLE SHAFT,
                                 TEFC, FR. 365T
 
HYDRAULIC PUMP DRIVE
MOTOR STARTER:                    SIZE 3, FULL VOLTAGE COMBINATION
                                 WITH FUSED DISCONNECT IN NEMA 12 ENCLOSURE
METHOD OF LUBRICATING TUBE END
TO BE POINTED:                   MANUAL
OIL COOLER:                      WATER TYPE WITH AUTOMATIC
                                 TEMPERATURE CONTROL
MAIN POWER SUPPLY:               460 V, 3 PH, 60 HZ
CONTROL POWER:                   120 VOLT, SINGLE PHASE
                                 FROM TRANSFORMER SUPPLIED
CONTROL LOGIC:                   PROGRAMMABLE CONTROL
IDLER ROLLER LOAD/UNLOAD STAND
NUMBER OF SUPPORT ROLLS:         12 ON APPROX. 60" CENTERS


TYPE OF ROLL :                    "V" SHAPED URETHANE
ROLL IDLE ROTATION.:               1-1/2" ANTI-FRICTION BEARING
                                  ON EACH SIDE OF ROLL
ROLL SUPPORT & VERTICAL ADJUSTMENT:   INDIVIDUAL PIVOT
                                      MOUNTING OF EACH ROLL WITH
INTERCONNECTING
                                      PULL BAR ADJUSTED BY MANUAL
                                      HANDWHEEL ON SCREW JACK
VERTICAL ADJUSTMENT RANGE
OF ROLLS:                               TO ACCOMMODATE FROM
                                      2" MIN. TO 5" MAX. O.D. TUBES
ESTIMATED EQUIPMENT SHIPPING WEIGHTS:
POINTER:                              15,000 LBS
HYDRAULIC PUMPING UNIT:               3,000 LBS
LOAD/UNLOAD STAND:                    7,000 LBS
TUBE GRIPPER JAWS FURNISHED:


ONE ( 1) PAIR SINGLE SIDED:           3.675"
DIES FURNISHED:                       3.375" &  3.100"
 
**PLEASE NOTE MANUFACTURERS SPECIFICATIONS**
**TEMPORARY SPECIFICATIONS SUBJECT TO REVISIONS**
**PRICE QUOTED AS IS WHERE IS SUBJECT TO PRIOR SALE**
**ALL SPECIFICATIONS ARE SUBJECT TO BUYER VERIFICATION**